1. Erweiterungsatz - 3 Stromklemmen und 3 Y-Kabel

    Für Installationen in Deutschland.

    Ändern

    Erweiterungsatz - 3 Stromklemmen und 3 Y-Kabel

    65,00 €
    Erweiterungsatz zum Addieren der Messungen von zwei Stromklemmen. Kann benutzt werden in Installationen mit einem zweitem Verbrauchs-Stromzähler (z.B. für eine getrennt gemessenen Wärmepumpe). Der Abstand des Smappee Monitors zu den beiden Messpunkten sollte 100 cm nicht überschreiten. Hinweise: Nicht geeignet zur Kombination von Solarzählern und Verbrauchszählern. Enthält: 3 Stromklemmen (Kabellänge: 150 cm, 50 Ampere), 3 Y-Kabel.
    - +
  2. Optical sensor

    Für Installationen in Deutschland.

    Ändern

    Optical sensor

    29,95 €

    Sensor to read out data on gas and water meters (typically gas) and to be used with the Smappee gas and water monitor.  This optical sensor is fit for meters with a mirror in the numbers 6, 8, 9 or 0 or for meters with a little a rotating wheel.  This item includes a sensor, a cable (1 meter)  to connect it to the Smappee monitor and 2 mounting strips for exact and easy installation on the meter.

    - +
  3. Magnetic sensor

    Für Installationen in Deutschland.

    Ändern

    Magnetic sensor

    19,94 €

    Sensor to read out data on gas and water meters (typically water) and to be used with the Smappee gas and water monitor. This magnetic sensor is fit for meters that have a little hole on the left, on the right or underneath, where the sensor can be inserted.  This item includes a sensor and a cable (1 meter) to connect the sensor to the Smappee monitor.

    - +
  4. Current Clamp, 50A, 10 mm

    Für Installationen in Deutschland.

    Ändern

    Current Clamp, 50A, 10 mm

    20,00 €
    Current Clamp, 50 Ampere, diameter 10 mm, for Smappee Monitor
    - +
  5. Current Clamp, 100A, 16mm

    Für Installationen in Deutschland.

    Ändern

    Current Clamp, 100A, 16mm

    29,00 €
    Current Clamp, 100 Ampere, diameter 16 mm, for Smappee Monitor
    - +
  6. Smappee Current Clamp, 200A, 24mm

    Für Installationen in Deutschland.

    Ändern

    Current Clamp, 200A, 24mm

    34,99 €
    Current Clamp, 200 Ampere, diameter 24 millimeter, for Smappee Monitor
    - +
  7. Extension Y-Cable

    Für Installationen in Deutschland.

    Ändern

    Extension Y-Cable

    6,00 €
    Y-Cable to add the measurements of two current clamps and connect them to one single Smappee Input. This Y-Cable can only be used with Smappee Non-Solar or 1-Phase (3 Inputs). Does not fit in Smappee Solar 3-Phase (6 Inputs). Can not be used to combine measurements of solar production and consumption. Please consult the Smappee Helpdesk before purchasing this item.
    - +
  8. Replacement V-Cable

    Für Installationen in Deutschland.

    Ändern

    Replacement V-Cable

    6,00 €
    Special cable to be used with the Smappee Solar Energy Monitor. This cable is required to connect a current clamp to an input of the Solar Energy Monitor. Hint: Do not confuse the V-cable and the Y-cable. They are completely different.
    - +
  9. Smappee Exchange Package to Solar Energy Monitor

    Für Installationen in Deutschland.

    Ändern

    Smappee Exchange Package to Solar Energy Monitor

    149,00 €

    Exchange Package to upgrade your Energy Monitor (non-solar) to a Solar Energy Monitor. You need to return your Smappee Energy Monitor for this exchange.  

    Important: Contact the Smappee Helpdesk before puchasing this Upgrade Package. 

    Shipment instructions: Keep your current power cable and 3 current clamps installed and do NOT send them back. Follow the instructions from our Helpdesk.

    Includes: 1 Smappee Solar Energy Montitor, 3 additional current clamps, and 3 V-Cables.

    - +
  10. Range extension set for Current Clamps

    Für Installationen in Deutschland.

    Ändern

    Range extension set for Current Clamps

    39,95 €
    This extension set extends the range of the current clamps with any standard Ethernet cable (RJ45). Important: This product is intended for expert use only. You should purchase this product only, after you have verified with the Smappee Helpdesk (support@smappee.com) that it is suitable for your particular situation! The set consists of 2 parts: one to connect to the current clamp, the other one to connect to the Smappee inputs. In between, you can use any regular Ethernet cable ("RJ45 straight-through") to extend the range of 3 current clamps up to 20 m (65 ft).

    Find more information here.

    - +
  11. Smappee Repair Service

    Für Installationen in Deutschland.

    Ändern

    Smappee Repair Service

    119,00 €

    Please get a Support Ticket Number before purchasing this product !

    Use this Smappee Repair Service if your Smappee Energy Monitor Home (Solar or Non-Solar) is defect after your warranty has expired. Send us your Smappee by a parcel service of your choice. Our experts will investigate the problem and fix it.

    Repair is guaranteed. If we can't fix the hardware defect, you will receive a refurbished and tested replacement unit. Without any loss of data.

    Important: Please buy the Repair Service product ONLY AFTER you have received a support ticket number with a confirmation by our helpdesk team! Just send an email to support@smappee.com and describe the problem and provide the serial number of your Smappee Energy Monitor.

    - +
  12. Remote Control for Comfort Plugs

    Für Installationen in Deutschland.

    Ändern

    Remote Control for Comfort Plugs

    9,95 €
    Remote Control for Comfort Plugs
    - +
  Loading...
This site uses cookies. By continuing to browse this site you are agreeing to our use of cookies. Find out more here.
x