1. Extension Set - 3 Current Clamps + 3 Y-cables

    For setup in United States.

    Change your country

    Extension Set - 3 Current Clamps + 3 Y-cables

    $65.00
    Extension set to add the readings of two current clamps. Can be used in homes that have two consumption meters (e.g. a separately metered heat pump). Make sure that the Smappee is installed within a distance of about 100 cm of both connection points. Note: Should not be used to combine solar readings with consumption readings. Includes: 3 current clamps (cable lenght: 150 cm: 50 Amps), 3 Y-cables.
    - +
  2. Optical sensor

    For setup in United States.

    Change your country

    Optical sensor

    $39.95

    Sensor to read out data on gas and water meters (typically gas) and to be used with the Smappee gas and water monitor.  This optical sensor is fit for meters with a mirror in the numbers 6, 8, 9 or 0 or for meters with a little a rotating wheel.  This item includes a sensor, a cable (1 meter)  to connect it to the Smappee monitor and 2 mounting strips for exact and easy installation on the meter.

    - +
  3. Magnetic sensor

    For setup in United States.

    Change your country

    Magnetic sensor

    $29.95

    Sensor to read out data on gas and water meters (typically water) and to be used with the Smappee gas and water monitor. This magnetic sensor is fit for meters that have a little hole on the left, on the right or underneath, where the sensor can be inserted.  This item includes a sensor and a cable (1 meter) to connect the sensor to the Smappee monitor.

    - +
  4. Current Clamp, 50A, 10 mm

    For setup in United States.

    Change your country

    Current Clamp, 50A, 10 mm

    $20.00
    Current Clamp, 50 Ampere, diameter 10 mm, for Smappee Monitor
    - +
  5. Current Clamp, 100A, 16mm

    For setup in United States.

    Change your country

    Current Clamp, 100A, 16mm

    $29.00
    Current Clamp, 100 Ampere, diameter 16 mm, for Smappee Monitor
    - +
  6. Current Clamp, 200A, 24mm

    For setup in United States.

    Change your country

    Current Clamp, 200A, 24mm

    $35.00
    Current Clamp, 200 Ampere, diameter 24 millimeter, for Smappee Monitor
    - +
  7. Extension Y-Cable

    For setup in United States.

    Change your country

    Extension Y-Cable

    $6.30
    Y-Cable to add the measurements of two current clamps and connect them to one single Smappee Input. This Y-Cable can only be used with Smappee Non-Solar or 1-Phase (3 Inputs). Does not fit in Smappee Solar 3-Phase (6 Inputs). Can not be used to combine measurements of solar production and consumption. Please consult the Smappee Helpdesk before purchasing this item.
    - +
  8. Replacement V-Cable

    For setup in United States.

    Change your country

    Replacement V-Cable

    $3.15
    Special cable to be used with the Smappee Solar Energy Monitor. This cable is required to connect a current clamp to an input of the Solar Energy Monitor. Hint: Do not confuse the V-cable and the Y-cable. They are completely different.
    - +
  9. Smappee Exchange Package to Solar Energy Monitor

    For setup in United States.

    Change your country

    Smappee Exchange Package to Solar Energy Monitor

    $159.00

    Exchange Package to upgrade your Energy Monitor (non-solar) to a Solar Energy Monitor. You need to return your Smappee Energy Monitor for this exchange.  

    Important: Contact the Smappee Helpdesk before puchasing this Upgrade Package. 

    Shipment instructions: Keep your current power cable and 3 current clamps installed and do NOT send them back. Follow the instructions from our Helpdesk.

    Includes: 1 Smappee Solar Energy Montitor, 3 additional current clamps, and 3 V-Cables.

    - +
  10. Range extension set for Current Clamps

    For setup in United States.

    Change your country

    Range extension set for Current Clamps

    $39.95
    This extension set extends the range of the current clamps with any standard Ethernet cable (RJ45). Important: This product is intended for expert use only. You should purchase this product only, after you have verified with the Smappee Helpdesk (support@smappee.com) that it is suitable for your particular situation! The set consists of 2 parts: one to connect to the current clamp, the other one to connect to the Smappee inputs. In between, you can use any regular Ethernet cable ("RJ45 straight-through") to extend the range of 3 current clamps up to 20 m (65 ft).

    Find more information here.

    - +
  11. Smappee Repair Service

    For setup in United States.

    Change your country

    Smappee Repair Service

    $159.00

    Please get a Support Ticket Number before purchasing this product !

    Use this Smappee Repair Service if your Smappee Energy Monitor Home (Solar or Non-Solar) is defect after your warranty has expired. Send us your Smappee by a parcel service of your choice. Our experts will investigate the problem and fix it.

    Repair is guaranteed. If we can't fix the hardware defect, you will receive a refurbished and tested replacement unit. Without any loss of data.

    Important: Please buy the Repair Service product ONLY AFTER you have received a support ticket number with a confirmation by our helpdesk team! Just send an email to support@smappee.com and describe the problem and provide the serial number of your Smappee Energy Monitor.

    - +
  Loading...
This site uses cookies. By continuing to browse this site you are agreeing to our use of cookies. Find out more here.
x